全球优质工业品一站式采购

恒仪多年行业经验 欢迎询价...

当前:首页 > 产品中心 > 热弥散流量开关FSW-6000andFSW-7000Series-美国omega
热弥散流量开关FSW-6000andFSW-7000Series-美国omega

热弥散流量开关FSW-6000andFSW-7000Series-美国omega

品牌/型号:美国omega()库号:H1052891

电联
保障:含运含税正品保障质保天

美国omega

型号:

热弥散流量开关FSW-6000andFSW-7000Series

Simple to Install and Low CostNo Moving Parts-Maintenance Free Reliability

  • Simple to Install and Low Cost
  • No Moving Parts-Maintenance Free Reliability
  • Optimal Temperature Compensation — Unaffected by Temperature Gradient
  • Can Operate in Temperatures up to 120°C (248°F) with Sanitary Option
  • Have a Maximum Working Pressure of 4,300 PSI (300 bar)
  • Chain of 8 LEDs- Integrated Flow Rate/Setpoint Indication
  • Can Be Used as a Level Switch
  • 产品描述

    The FSW-6000/7000 Series are thermal flow switch monitors designed to monitor flow status and also used to detect level of liquids, air and gas. A chain of 8 LED’s gives the user a visual indication of the flow rate. In addition, there isalso a dichromatic LED, which shows the switch point status of the unit. The sensing element and connection of the FSW-6000/7000 Series are made with 316 SS. The standard enclosure is glass-filled nylon and is also available in an aluminum enclosure for hazardous environments. The FSW-6000/7000 Series can be made with a great variety of process connections such as threaded, flange, or sanitary.

    The FSW-6000/7000 Series line of thermal flow switch monitors is based on the principle of thermal dispersion. A typical configuration uses two platinum Resistance Temperature Detectors (RTD’s) set within the tip of the sensor. One RTD is heated a few degrees above the temperature of the medium and the other RTD is used as a reference, sensing the actual process temperature. The second RTD also monitors the temperature of the medium, as any changes in temperature must be compensated for in the first RTD. As the process medium flows over the tip of the sensor it disperses some of theheat from the first RTD. The temperature change between the two RTD's signals the probe’s electronics and the switch changes state once the set point has reached.

    The FSW-6000/7000 Series may be installed in a pipe or tank using the thread or connection provided. Use only the hexagon when tightening to achieve a seal, do not use the body. The body should be rotated after tightening to leave the cable gland in suitable orientation. The FSW-6000/7000 Series is not affected by its fixing position so it may be installed at any angle around the pipe. However, it is recommended that with horizontal pipe runs the sensor should be installed on the side, into the middle of the pipe. In vertical pipes, the FSW-6000/7000 Series should be installed when there is flow in an upward direction against gravity. Care should be taken when installing the sensor that the probe extends clear of the pipe’s internal wall and is fully immersed into the flow. In pipes with smaller diameters, some care should also be taken so that the sensor is not screwed too far into the line.

    SPECIFICATIONS
    Accuracy: ±10% of setpoint
    Repeatability: ±1% of setpoint
    Power Supply:
        FSW-6000: 85 to 240 Vac (50/60 Hz)
        FSW-7000: 24 Vdc ±10%
    Temperature Range:
        Process: -20 to 80°C (-4 to 176°F) [sanitary option to 120°C (248°F) for CIP]
        Operating: -20 to 60°C (-4 to 140°F)
    Max Pressure: 300 bar (4351 psi)
    Protection Class: NEMA 4 (IP65)
    Wetted Materials: 316 SS
    Enclosure Material: Glass filled nylon standard or aluminum die cast option
    Process Connection: ½ to 1½ NPT, Tri-Grip™, or flange (others available, consult Flow Engineering Department)
    Output: 250 Vac SPDT 5 A relay
    Switch Point Adjustment: Potentiometer
    Bargraph:
        Green LED: Flow rate above setpoint
        Yellow LED: Flow is at above setpoint
        Red LED: Flow is below setpoint
    Switch Point Status:
        Red LED: No flow
        Green LED: Flow
    Response Time: 1 to 10 seconds
    Max Start up Delay: 12 seconds
    Switching Range: 3 cm/s to 3 m/s (0.09 to 9.84 ft/sec) (liquid), 5 cm/sec to 15 m/sec (0.16 to 49 ft/sec) (gas)
    Dimensions:
        Nylon Head: 88 Dia x 80 mm H (3.5 x 2.5" H)
        Aluminum Head: 88 Dia x 108 mm H (3.5 x 4.25")
        Insertion Length: 13⁄8, 2 and 3" standard, for other lengths consult Flow Engineering
         Maximum insertion Length is 36"

        Weight: Approx 680 g (1.5 lb)
  • 联系我们

    联系方式

    推荐品牌

    采购工业品为什么选恒仪?

    youshi

    全球多地设有办事处

    恒仪总部设在河北保定,北京、德国、美国、香港设有办事处,产品采购售后服务更方便。

    youshi

    全球1000多家供应商合作

    恒仪与全球超过1000家工业品供应商密切合作,产品更全。

    youshi

    源头采购 价格更低

    恒仪直接与全球各品牌厂家采购,省去中间商、代理商差价,价格更低、产品质量有保障。综合利润不超5

    youshi

    经验丰富 服务更好

    我们的团队核心成员均来自行业知名企业,经验超过10年,为您提供更好的服务。

    youshi

    正品保障 更放心

    每一件产品均全球各品牌原厂采购,保证100%正品、保证质量、保证售后。拒绝任何假货、次品货。

    youshi

    空运直发 货期更快

    恒仪与国际知名物流公司合作,非限制产品,只发空运,货期更快。让客户更快拿到产品。

    youshi

    技术雄厚 售后保障

    恒仪设有专业的技术及售后团队,为您解决各类产品使用问题,及时为您处理售后问题,服务有保障。

    youshi

    一站式服务 客户更轻松

    恒仪采购全程一站式服务,让客户轻轻松松获得国际优质工业品,不再担心各类采购问题。

    关于恒仪

    恒仪公司于2015年在北京成立,2016年公司将总部搬迁至河北保定市。2017年在美国、德国、香港、建立了办事处。通过几年发展公司的实力与规模不断壮大,如今直接通过各国办事处向全球各国品牌厂家采购工业品,包括:仪器仪表、机电设备、工控、机械、自动化等等工业品,保证了产品在质量、价格、货期、售后上的优势;[ 查看详情 ]

    河北恒仪电子科技有限公司

    电话:0312-6795158

    邮箱:pm@hinstr.net

    地址:河北省保定市莲池区瑞兴路19号

    关于我们联系我们人才招聘

    河北恒仪电子科技有限公司版权所有 侵权必究

    河北恒仪电子科技有限公司版权所有 侵权必究!冀ICP备16029740号-8